CCUSE "Laboratory of biosafety, quality of food products and food safety"
Center for collective use of scientific equipment
The list of available orders for equipment of the CCUSE
17.25 thousands of euros
Qualitative and quantitative characteristics of food products, raw materials and other materials
To analyze and control the quality of raw materials, semi-finished products and finished products according to the appropriate methods
39.02 thousands of euros
Equipping the Kinexus Pro+ rotary rheometer with additional parallel plates-geometries will allow to expand the measurement range of a wide range of materials, for Newtonian and non-Newtonian fluids with low viscosity to more viscous dispersed systems: gel-like materials, soft and hard substances, polymers and others systems The wide range of plate sizes is due to the measurement of materials with different rheological parameters.
Smaller diameter geometries are used for samples with high viscosity, and larger ones (Ø50 mm) for materials with low viscosity (0.1 Pa*s). In addition, geometries with a toothed surface are used to study emulsions and suspensions, which are prone to slipping. This manifests as an early drop in viscosity during shear rate measurement, resulting in a sudden drop in viscosity and suspected slippage. This surface interface provides additional adhesion of the material to the geometry, and stimulates the smooth flow of the material. Using geometries of different diameters will allow for a more smooth variation of the gaps between the geometries in the measurement and follow general rules of thumb, and will provide sufficient interaction to eliminate wall effects that cause artifacts in the results. The possibility of combining the geometries of the cone and the plate will allow to measure the geometries at the set gap (automatically controlled by the software). This allows absolute viscosity to be measured when the entire sample is subjected to the same shear rate, a significant advantage over parallel plate geometries that have a range of shear rates along their radii and only the average value is reported. For the study of materials and systems sensitive to temperature effects, or in which phase changes/transitions occur under the influence of temperature, elimination of temperature gradients, and when measuring temperatures significantly higher or lower than the ambient temperature, a cartridge is needed for setting temperatures when measuring from -5C up to 180°C, or from -40°C with an active heat exchanger. The cartridge is a combination of a Peltier element with additional heaters for active control of radial and vertical heat losses from the local environment of the sample with a resolution of 0.01°C, with measurement stability of +/- 0.1°C.
74.34 thousands of euros
For the dynamic formation of the image of particles, and obtaining an idea of the dispersion of particles
The Particle Insight Shape Module is coupled in series with the Liquid Dispersion Module of the Mastersizer 3000 Particle Size Analyzer. The module complements the laser diffraction particle size data results of the Mastersizer 3000 analyzer and provides particle size distribution information to the particle images. , their quantitative data, data on the shape of particles. The advantages of this module include the provision of high-speed dynamic imaging technology with high resolution: a digital camera with a speed of up to 127 FPS and a resolution of up to 5 MP, obtaining images of individual particles and liquid dispersions of particles from 1 to 800 μm, the ability to create thumbnails of images, their save for review after run, obtain quantitative data on particle size and shape, including data on particle width and elongation.
31.95 thousands of euros
For a deeper understanding of the processes and transformations that occur during the analysis of particles of powder materials and particles of suspensions
The acquisition of the BeVision M1 automatic image scanning system will complement the existing Mastersizer 3000 particle size analyzer with dry and wet dispersion modules and enable high-resolution analysis of particle morphology.<br /> The system is equipped with a microscope, programmable motorized stage, autofocus function and high resolution CMOS. The device can capture and recognize each individual particle, automatically combining the images into a large overview image.<br /> Features and advantages include a wide range of measurements: 1 - 10,000 μm, compliance with the ISO 9276-6 standard, high reproducibility of measurements, the presence of a stage with high positioning accuracy, the presence of 24 different parameters of particle size and shape.<br /> The BT-910 dry powder dispersion module is used to prepare samples before measurements. The module is designed for rapid dispersion of dry powder samples and subsequent analysis of particle size and shape using BeVision M1. This module can disperse both coarse and brittle materials under controlled conditions without any particle damage, providing an efficient and reproducible method of sample dispersion. It is suitable for various applications. Application occurs without additional reagents, with uniform application of the material on the glass slide.
34.32 thousands of euros
Spectrophotometer CM-5 is designed to measure color by color parameters (L*, a*, b*) of all surfaces of solid materials, powders, pastes, liquids, granules, food products and ingredients, the surface of packaging materials, biopolymer films and gels, determining the freshness of products during storage. Kolov is an indicator of quality and safety, which is directly dependent on the quality of raw materials, recipe components and the type of technological factors influencing the food product.
The need for measurements is related to the variety of parameters that require analytical monitoring in the food laboratory, where color is the only directly obvious indicator of quality, and deserves due attention through objective and repeatable measurement of raw materials, production processes and the final product.<br /> These researches will contribute to the reduction of waste, allow to detect spoilage of products, control the quality of ingredients, and technological processes at all stages of production. This will allow to investigate the influence of storage conditions, thermal effects on the quality and safety of food products, will allow to control and adapt to prevent unwanted changes that lead to increased losses and waste. Depending on the sample, the CM-5 spectrophotometer can perform a variety of color measurement functions, measuring color samples by reflectance or transmittance with the ability to set tolerances for each measurement.